Mercedes S-Class W-220

since 1998 release

Repair and operation of the car



Mercedes W220
+ Mercedes-Benz cars of the class S (W220)
+ Operation manual
- Routine maintenance
   Specifications
   Active system of the warning of the term of approach planned THAT (ASSYST)
   Schedule of routine maintenance
   General information on control
   Check of levels of liquids, control of leaks
   Check of a condition of tires and pressure in them. Designation of tires and disks of wheels. Rotation and replacement of wheels
   Replacement of motive oil and oil filter
   Check of the brake system
   Check of fuel system
   Check of a state and replacement of hoses of a motive compartment, localization of leaks
   Check of a condition of ridge belts of the streaming drive of auxiliary units
   Check of functioning of the cooling system and frost resistance of cooling liquid. Liquid replacement
   Check of a condition of system of production of the fulfilled gases
   Check of level of oil of automatic transmission
   Visual check of tightness of automatic transmission
   Check of a state component of a suspension bracket and steering
   Check of a condition of protective covers of power shafts
   Check of level of liquid of system of hydrostrengthening of a wheel
   Check of the air conditioning system
   Lubricant of limiters of doors and cylinder of the lock
   Visual control of a seat belt and block of a safety cushion
   Check of operability of headlights and horn
   Check of a state, adjustment and replacement of brushes of screen wipers
   Check of a condition of the battery, care of it and charging
   Replacement of an element of the filter of air of salon / coal filter of purification of air
   Replacement of brake fluid
   Check and replacement of spark plugs. Check of a condition of high-voltage wires
+ Engine
+ Cooling system and heating
+ Power supply system and release
+ Engine electric equipment
+ Automatic transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Schemes of electric equipment






Replacement of motive oil and oil filter

The long contact of skin with the fulfilled motive oil is quite dangerous. Use protective cream and put on gloves during this procedure. Replace the clothes which became impregnated with oil immediately.


Recommendations

Frequent replacement of motive oil is the main preventive procedure of service, to the available amateur mechanic. Eventually oil is subject to fluidifying and pollution that leads to premature wear of the engine.

Motive oil can be extorted by means of the special probe (is available at gas stations) through a tube of the probe of measurement of level of oil. After that it is necessary to fill system with oil, as a rule.

Do not pour out the fulfilled oil together with household waste or otherwise. It can cause environmental pollution.

Expediently when replacing oil to fix on the engine a label with brand of oil and its viscosity.

Use of oils of various types adversely affects operation of the engine. It is not recommended to mix various brands of oils also. Motive oils of the same type and brand, but various viscosity in necessary cases, in particular in off-season, can mix up.

Necessary tool:

· A viewing ditch or the hydroelevator with supports (if oil is not sucked away).
· A head for an otvorachivaniye of a drain stopper.
· The special tool for a filter otvorachivaniye (a key for the filter, a tape key or the HAZET 2172 tool).
· Capacity for collecting oil (if oil is not sucked away) with a capacity not less than 6 l.

Necessary spare parts and expendables:

· Only if oil is not sucked away: an aluminum or copper sealing ring for a drain stopper (are sometimes delivered together with an oil filter).
· Oil filter.
· Necessary amount of motive oil. Apply the oil resolved by the manufacturer, address Specifications.

Removal of motive oil

Motive oil can be also removed with an exhaustion method, by means of the probe, through a probe opening.

 PERFORMANCE ORDER

1. Warm up the engine up to the working temperature (temperature of oil of +60 °C).
2. Horizontally lift the car.
3. Substitute under the case pallet capacity for collecting the fulfilled oil.

4. Turn out from the case pallet a drain stopper (1 on an illustration) and completely merge oil.

 Attention! If in the fulfilled oil there are at a large number a metal shaving and products of wear, it indicates existence of zadir, for example, in bearings of a bent shaft and conrod bearings. For an exception of damages after the made repairs it is necessary to clear oil channels and hoses carefully. It is in addition necessary if is available, to replace the oil heater.

5. Then it is necessary to screw a drain stopper with a new sealing ring. It is not necessary to exceed the inhaling moments specified in Specifications, otherwise it can lead to violation of tightness and damages.
6. Lower the car on wheels.


Replacement of an oil filter

 PERFORMANCE ORDER

1. Turn off from below an oil filter. For an otvorachivaniye of an oil filter there is a special tool, for example, of HAZET 2172. It is also possible to enter sideways into the filter the peaked screw-driver. After that at once oil begins to pour out - substitute capacity.

2. Clear a flange of an oil filter fuel. Remove the possible remains of laying from a flange.
3. Grease new laying of an oil filter with a thin layer of motive oil.
4. Strong tighten a new oil filter only by effort by hand. After laying will lie down to a flange, tighten the filter on a turn floor. Pay attention to the remarks given on the filter case.
5. Tighten a stopper of a drain opening with a new ring the moment specified in Specifications.


Gas station of motive oil

 PERFORMANCE ORDER

At the first start of a turbodiesel after replacement of oil it is necessary to watch that the engine at first worked on single turns, the control lamp of pressure of oil will not go out yet. Only after achievement of necessary pressure of oil it is possible to increase gas. If gas is given at the burning control lamp, owing to insufficient amount of oil the turbocompressor can be damaged.

1. Open a cover and pour in new oil at a jellied mouth of a cover of a head of cylinders.
2. When replacing oil apply new oil of the same type and, whenever possible, the same brand. At each replacement of oil attach the plate on which specify brand and viscosity of the filled-in oil to the engine.

 Attention! It is recommended to fill in oil 0.5 l smaller at first. Warm up the engine and in a few minutes, by means of the index, check oil level, if necessary add. Remove surplus of oil, otherwise consolidations of the engine and the catalytic converter can be damaged.


3. Add oil to MAX tag. If the level of oil is higher, oil needs to be exhausted.

4. After a trial trip check tightness of a drain stopper and an oil filter, if necessary carefully add oil.
5. 3 minutes later after an engine stop check oil level again, if necessary add or remove oil.